Description
Why Producers Move Up to a 5000L Oak Vat
A 5000-liter oak tank holds the contents of about twenty standard barrels. Distilleries and wineries switch to it when barrel handling becomes the bottleneck: fewer vessels to rack, one topping-up schedule, and a single lot number for an entire bottling run. It suits whiskey, brandy, rum, and vodka spirit where consistent oak contact matters more than small-batch variation.
Staves, Hoops, and Hardware
We build from French oak (Quercus robur, tight grain, slower tannin release) or American white oak (Quercus alba, higher lactone content, more vanilla and coconut). Staves are quarter-sawn and air-dried outdoors for 24 to 36 months, then machined to 32 to 45 mm. Nothing is glued. Head and side joints seal by swelling after the first fill, so the soak schedule in the first two weeks decides whether the tank stays tight.
Hoops are hot-dip galvanized steel, or stainless 304 where humidity is high or washdown is frequent. Common fittings: a 316L sample valve, a stainless racking arm, a top manway, and a silicone or oak bung. Oak is not a CIP surface. Cold water rinse, sulfur wicks or ozone, and no caustic, no chlorine, no water above roughly 40C.
Typical Specifications
| Parameter | Specification |
|---|---|
| Nominal capacity | 5000 L (1,320 US gal) |
| Wood | French oak or American white oak |
| Stave thickness | 32 to 45 mm |
| Air drying | 24 to 36 months |
| Hoops | Galvanized steel or SS304 |
| Fittings | SS316L sample valve, racking arm, top manway |
| Finish | Sanded exterior, optional clear lacquer |
Questions We Get Before Quoting
Working capacity? Plan a 4,700 to 4,800 L fill volume. Leave 3 to 5 percent ullage for expansion and headspace management.
French or American? American oak reads faster and louder. French oak is slower and tighter. If the tank is a blending vessel rather than a long-term aging vessel, the choice matters less than the toast level of any inserts you add.
Can temperature be controlled? Yes, with an external stainless cooling panel or a drop-in coil. Oak insulates poorly compared with a jacketed stainless tank, so size the cooling surface for ambient room swings, not for the liquid volume alone.
Site assembly? Tanks ship assembled. Hoops are re-driven after the first soak and again at three months, then once a year.
Tell us your capacity, spirit or wine type, target aging time, room temperature range, and door clearances. We can recommend the wood, stave thickness, hoop material, and fitting layout for your site.
Related products
Wine Storage & Fermentation Tank 1000L–10000L Dimple Plate Cooling
Dimple plate cooled wine storage and fermentation tanks from 1000 L to 10000 L, built in SUS304 or SUS316L with full-penetration welds, pickled and passivated interiors, and 3 bar glycol jackets. Available with conical or sloped bottoms, CIP, racking arms and pressure relief for wineries of any scale.
2000L Custom Wine Fermenter Tank with Cooling Chiller Vessel
A 2000L wine fermenter tank for small wineries, brewpubs, and contract producers. Built in SUS304 or SUS316L with glycol cooling jackets, sanitary welds, CIP fittings, and customizable cone, manway, and ports. Use it for fermentation, cold stabilization, or storage. Share batch size, wine type, tank count, and space so we can recommend the right cooling area and configuration.
1500L Red Wine Fermentation Tank Dimple Jacket Temperature Control for Wineries
A 1500L stainless steel red wine fermentation tank with dimple jacket temperature control, built for small and mid-size wineries. The jacket holds fermentation temperature and supports cold soak, while the sloped bottom, side must door and tri-clamp fittings keep cap management and cleaning practical. Available in SUS304 or 316L.
10HL-100HL Wine Fermentation Tank with Spiral Cooling Jacket
A 10–100 HL wine fermentation tank built with a spiral glycol jacket that covers the cone and lower cylinder, sized against your crash-cooling target rather than peak ferment heat alone. SUS304 or 316L construction, full-penetration TIG welds, optional 0.4–0.8 µm interior polish, CIP spray ball and racking arm as standard.
100HL Red White Wine Fermentation Tank Dimple Cooling Jacket Commercial Winery
This 100HL red and white wine tank is built for commercial wineries that need reliable fermentation and storage. The dimple cooling jacket controls temperature during active fermentation, while SUS304 or 316L contact surfaces, CIP connections, and insulated cladding support daily cellar work. We size jacket coverage, fittings, and cone details around your batch size, wine type, and glycol supply.
1000L-3000L Stainless Steel Wine Fermentation Tanks for Red & White Wine
Stainless steel wine fermentation and storage tanks from 1,000 L to 3,000 L, built in SUS304 or 316L with dimple cooling jackets, CIP spray balls, racking arms and pressure relief. Sized for small and mid-size wineries fermenting red and white lots, with configurable fittings, insulation and glycol circuits for temperature-controlled cellars.
1000L-3500L White Wine Fermentation Tank with Cooling Jacket for Fruit Wine
Jacketed white wine and fruit wine fermentation tanks in 1000L, 2000L, 3000L and 3500L working volumes. SUS304 or 316L construction, dimple cooling jackets, conical or sloped bottoms, CIP spray ball and tri-clamp glycol connections. Built to order with hydro-tested shells and jackets, safety valves and racking arms for small wineries and commercial cellars.
10000L 12000L 20000L Wine Storage & Fermentation Tank Stainless Steel
Stainless steel 10,000 L, 12,000 L and 20,000 L tanks for wine storage and fermentation. Built in SUS304 or 316L with dimple cooling jackets, sloped or 60° conical bottoms, CIP spray balls and matched pressure/vacuum relief valves. We size jacket area and fittings around your batch rhythm, glycol supply and cleaning setup.
Although there were a few minor issues, thanks to Polly’s help, it looks brilliant and has brought my little distillery quite a few new customers.
Very good！！I see now in my texting to you that in my excitement over having the installation here in the USA I totally forgot to give you and the company of ACE a very big compliment on the quality of the whole Installation!! It all looks fabulous and the way you packed it in the container was extraordinary!! I am very impressed with your company and want to say a big thank you to everybody who worked on my order!!
We have been using this still for a few batches now making whiskey, gin and a few other spirits and we are very happy with the results so far. The gear works well and gives good control during distillation. The spirit comes out clean and consistent from batch to batch and we have gotten the flavor profile we were looking for. It has also been easy to operate and maintain. It has been a great addition to our distillery and I’d definitely recommend it to other craft distillers looking for reliable equipment.”
Polly is the man! I highly recommend him and this products they produce! I’m very satisfied. she communicates very well and the quality of workmanship is excellent! Shipping was exceptional. Thannks Polly and team
It took 60 days from ordering to delivery, and it looks like a work of art. Thank you to Polly for her help.
It was quite a big job to put the distiller together, so I asked a friend to help me, and I managed to get it done in just eight hours. I’m really pleased with it – it looks brilliant.Ryan Murphy
We are so happy with our new copper distillation system from ACE Distillery Equipment. The equipment is of a fine quality, well crafted and beautifully finished.
The whole process from manufacturing, shipping, installation to commissioning was seamless. The ACE team were professional, responsive and very knowledgeable. They helped us complete the installation successfully and gave great technical support.
It still looks amazing in our distillery and does exactly what it says on the tin. We highly recommend ACE to anyone looking for reliable and high quality distillation equipment.
Thank you ACE team for the great work!”
I want to express my 100% satisfaction with Ace . The service was outstanding: quick, professional, and friendly. Polly provided excellent support throughout. The delivered 100 gallon copper pot still distillery equipment product perfectly meets my expectations and stands out fo r its excellent quality. I feel well taken care of and will recommend you without hesitation.
Thank you for the great service.
Best regards,
Oliver Brown
