Description
2000L SUS304 Dimple Jacketed Conical Fermenter
This 2000L conical fermenter is built for breweries that need consistent fermentation temperature without overcomplicating the tank design. We manufacture the shell and cone from SUS304 stainless steel, with dimple jackets on the cone and lower cylinder. For a 2000L batch, that cooling area is usually enough to pull active fermentation heat down to lager or ale targets, provided the glycol system is sized correctly.
Material choice matters. SUS304 handles typical beer, CIP chemicals and cold-side service. If you run high-chloride water, long sour contact, or need extra corrosion margin, we quote 316L. Inner surfaces are pickled, passivated, and polished to roughly 0.4–0.8 μm Ra. Product-contact welds are full-penetration and ground smooth at the cone, manway and jacket seams. Sanitary clamp fittings, DIN or SMS, match your hoses and valves.
Temperature control comes from the dimple jacket and glycol flow. The jacket is not the product pressure vessel; working pressure applies to the tank interior. We normally build the inner tank for 0.2–0.3 MPa working pressure and fit a mechanical relief valve and pressure gauge. Cone angle is 60° for most ales and lagers, but we adjust to 70° or 90° for yeast discharge or dry hopping access.
CIP runs through a rotating spray ball in the dome, with separate ports for CO2, dry hopping, sample valve, racking arm and pressure relief. Small brewpubs often choose one jacket zone and manual valves. Commercial breweries ask for separate cone and cylinder zones, a pressure-rated sight glass, and butterfly valves tied to a central CIP skid.
Typical specifications
| Capacity | 2000L working volume |
| Material | SUS304, 316L optional |
| Jacket | Dimple jacket, cone and cylinder |
| Inner pressure | 0.2–0.3 MPa working |
| Surface finish | 0.4–0.8 μm Ra product contact |
| Cone | 60°, 70° or 90° |
| Connections | DIN, SMS, tri-clamp |
FAQ
Can this tank ferment lagers? Yes, if the glycol system and jacket zones are sized for the temperature pull-down. A 2000L lager tank in a warm room needs more cooling capacity than an ale tank.
Do I need 316L? Not for standard beer. Choose 316L when chloride levels, sours, or long acid contact make 304 risky.
How do I connect CIP and beer lines? We match port sizes to your valve standard. Send your P&ID or existing hose schedule before fabrication.
Tell us your batch size, beer type, number of fermentation tanks and available space. We can recommend the tank volume, cooling area and configuration for your brewery.
Structure of a Beer Fermentation Tank
Related products
1000L Stainless Steel Unitank Fermenter for Ale Lager Stout Craft Brewing
1000L stainless steel unitank for ale, lager, stout and porter production. A combined fermentation and conditioning vessel with dimple cooling jackets, 2 bar working pressure, CIP spray ball and a 60° cone. Built in SUS304 or 316L with sub-0.6µm interior polish. Suits brewpubs and small commercial breweries stepping up to wholesale volume.
1000L Craft Beer Fermenter with Top Manway & Dimple Cooling Jacket
A 1000L craft beer fermenter with a 60° cone, top manway and dimple cooling jacket. Built in SUS304 or 316L with a pickled, passivated interior, glycol jacket, CIP spray ball and tri-clamp fittings. Suited to brewpubs and small production breweries running repeatable fermentation schedules. Specifications, pressure ratings and selection guidance for your brewery.
1000L Isobaric Beer Fermenter Regulated Brewery Fermentation Chamber
A 1000 L isobaric beer fermenter gives breweries pressure-capable fermentation, maturation, and carbonation in one vessel. This regulated chamber design uses SUS304 or SUS316L, glycol cooling jackets, 60° or 70° cones, and CIP-ready ports. We build each tank to your batch size, beer style, pressure target, and cellar layout.
1000L Conical Beer Fermenter with Glycol Jacket & SUS304 Tank for Microbrewery
A 1000L conical fermenter built in SUS304 or 316L with two-zone glycol jackets, 60° cone and 1.5 bar working pressure. Suited to taproom breweries and brewpubs moving past 5–7 BBL batches. Standard tri-clamp fittings for racking, dry hopping and CIP, with customizable control, insulation and pressure options for microbrewery use.
1000L Stainless Steel Conical Beer Fermenter Unitank with Cooling Jacket
A 1000L conical unitank built for real cellar conditions: 60° cone, SUS304 or 316L shell, dimple cooling jacket on cone and lower cylinder, and 1.5 bar working pressure with a 3 bar option. We cover fabrication details, glycol sizing, CIP routing and how to choose between two 1000L tanks and one larger vessel.
Conical Beer Fermenter Tank 1000L 1500L 2000L 3000L with Cooling Jacket
Jacketed conical fermenters from 1000L to 3000L, built in SUS304 or 316L with dimple cooling jackets on the cone and lower cylinder. Rated to 2 bar working pressure for unitank carbonation. Includes CIP spray ball, racking arm, dry-hop port and sample valve. Sized for brewpubs through regional breweries.
10000L Conical Beer Fermentation Tank | 100HL Stainless Steel Fermenter
A 10,000 L conical fermenter suits 100 hl brewing schedules, double-batch 50 hl brewhouses, and commercial lager or ale production. Built in SUS304 or SUS316L with dimple glycol jackets, 0.2–0.3 MPa working pressure, CIP spray ball, and optional dry hopping or carbonation ports. Configured to your batch size, available height, and cooling capacity.
Although there were a few minor issues, thanks to Polly’s help, it looks brilliant and has brought my little distillery quite a few new customers.
Very good！！I see now in my texting to you that in my excitement over having the installation here in the USA I totally forgot to give you and the company of ACE a very big compliment on the quality of the whole Installation!! It all looks fabulous and the way you packed it in the container was extraordinary!! I am very impressed with your company and want to say a big thank you to everybody who worked on my order!!
We have been using this still for a few batches now making whiskey, gin and a few other spirits and we are very happy with the results so far. The gear works well and gives good control during distillation. The spirit comes out clean and consistent from batch to batch and we have gotten the flavor profile we were looking for. It has also been easy to operate and maintain. It has been a great addition to our distillery and I’d definitely recommend it to other craft distillers looking for reliable equipment.”
Polly is the man! I highly recommend him and this products they produce! I’m very satisfied. she communicates very well and the quality of workmanship is excellent! Shipping was exceptional. Thannks Polly and team
It took 60 days from ordering to delivery, and it looks like a work of art. Thank you to Polly for her help.
It was quite a big job to put the distiller together, so I asked a friend to help me, and I managed to get it done in just eight hours. I’m really pleased with it – it looks brilliant.Ryan Murphy
We are so happy with our new copper distillation system from ACE Distillery Equipment. The equipment is of a fine quality, well crafted and beautifully finished.
The whole process from manufacturing, shipping, installation to commissioning was seamless. The ACE team were professional, responsive and very knowledgeable. They helped us complete the installation successfully and gave great technical support.
It still looks amazing in our distillery and does exactly what it says on the tin. We highly recommend ACE to anyone looking for reliable and high quality distillation equipment.
Thank you ACE team for the great work!”
I want to express my 100% satisfaction with Ace . The service was outstanding: quick, professional, and friendly. Polly provided excellent support throughout. The delivered 100 gallon copper pot still distillery equipment product perfectly meets my expectations and stands out fo r its excellent quality. I feel well taken care of and will recommend you without hesitation.
Thank you for the great service.
Best regards,
Oliver Brown
